img

HIGH PERFORMANCE POLYURETHANE ACRYLIC WATER-BASED


POLYDEK SUPER P

HIGH PERFORMANCE POLYURETHANE ACRYLIC WATER-BASED,
SINGLE COMPONENT WATERPROOFING MEMBRANE

DESCRIPTION:
POLYDEK SUPER P is a highly elastic & high performance, liquid-applied waterproofing membrane of polyurethane and acrylic polymer. It consists of a very elastic polymer with the inherent flexibility that allows the membrane to accommodate movements in the substrate. It works as a seamless membrane that performs and adapt to any construction requirements in varied climatic conditions.

CALL US 0913 404 017 - 0985 406 777 NOW


USES

•    Fire Walls
•    Exposed concrete slab roofs
•    New & old roofs / walls
•    Car porch roofs
•    Tiles roofs
•    Fibre cement boards
•    Metal surfaces
•    Gutters

ADVANTAGES

•    Waterproofing - Prevents further ingression of water in old and new concrete.
•    Durability - Enforced with fibre glass matt increases film tensile strength and wear resistance.
•    Flexible – High elastic enable bridging of hairline cracks and accommodates minor joint movements.
•    Weather Resistant - Excellent UV resistance.
•    Trafficable - Able to withstand foot traffic.
•    Cost Effective - Repairs damaged concrete by direct application without additional re-construction.
•    Ease of Application - Brush, roller or airless spray applied.
•    Solvent Free - Operators do not need extra respiratory protection.
•    Ease of Maintenance – Fungus & mold are free on apply surfaces
 

PRODUCT PROPERTIES
 

Colour

White & Grey

Chemical Base

Polyurethane modified Acrylic

Density

1.25 kg/litre of fresh liquid membrane

Tensile Strength

> 3 N/mm2) ( ASTM D412)

Elongation At Break

> 300%(ASTM D412)

Crack Bridging (mm)

2 mm No cracks was observed (ASTM C836:2006)

Weather resistance

UV Resistant

Solid content %

70% (ASTM 2369)

COVERAGE

Specification for walls and firewalls
The system consists of the following sequence;
1.    1 coat of Greenshield Primer
2.    1 coat of POLYDEK SUPER P
3.    1 coat of POLYDEK SUPER P

Specification for concrete and roofs
The system consists of the following sequence;
1.    1 coat of Greenshield Primer
2.    1 coat of POLYDEK SUPER P
3.    1 layer of Fibremesh
4.    1 or 2 coats of POLYDEK SUPER P

NOTE:  * 3 hours is needed for the drying of each coat of POLYDEK SUPER P before the application of the next coat.

MIXING: No mixing is required.

CURING:  Allow 24 hours between coats. A final curing time of 48 hours is adequate at normal working temperatures. Ensure curing is complete before laying thermal insulation boards, mechanical protect and other coverings.

Low Temperatures and high atmospheric humidity will slow down the curing rate, and vice versa.

CLEANING EQUIPMENT: Clean equipment with soapy water followed by rinsing with clean water. Flush mineral spirits through the spray equipment to prevent rust.

PACKAGING AND APPEARANCE

•    20 litre /pail
•    Colours – White & Grey (Special color are available through request to Greenseal office.)

STORAGE AND SHELF LIFE

POLYDEK SUPER P has a shelf life of 12 months. Keep containers tightly closed and away from ignition sources. Do not expose it to direct sunlight or leave it too long in the open air.

PRECAUTION : Do not apply POLYDEK SUPER P if weather is imminent before the coat is dry thoroughly, or when temperature is expected to drop below 5oC.
Newly applied POLYDEK SUPER P should be protected from rain, extreme heat and moisture during the first few hours.

Please contact Greenseal Products (M) Sdn Bhd for further technical assistance.

HEALTH, SAFETY AND CLEANING

It is recommended that the applicator wears a safety goggles and gloves. Avoid prolonged contact with exposed skin, and keep away from mouth and eyes. In case of skin contact, wash areas with soap and water. If contact with eyes, rinse thoroughly with clean water. Seek medical attention immediately if irritation persists.

Guarantee

The information contained in this leaflet is based on our experience and technical knowledge, obtained through laboratory testing and from bibliographic material. GREENSEAL reserves the right to introduce changes without prior notice. Any use of this data beyond the purposes expressly  
specified in the leaflet will not be the Company’s responsibility unless authorized by us. Our guarantee covers exclusively the quality of the manufactured product. We will not accept any responsibility exceeding the value of the purchased product.


Greenseal Products (M) Sdn Bhd, Lot 5 & 7, Jln 35/10A, Taman Perindustrian IKS, Mukim Batu Caves,
68100 Kuala Lumpur, Malaysia. Tel : 603-61882298    Fax : 603-61861298    
E-mail : enquiries@greenseal.com.my URL: http://www.greenseal.com.my
Greenseal is certified by MS ISO 9001:2008 & ISO 140012004

 

Waterproofing Material